一种基于天基的瞬变电磁高分辨探测小尺度太空碎片的方法          下载免费PDF全文

李文翰  李贺  鲁凯亮  崔洪亮 《地球物理学报》2018,61(12):5066-5076

目前，太空碎片的天基探测方法一般是激光雷达法.由于激光雷达的辐射频率一般为可见光或红外波段，在分辨厘米量级的太空碎片时具有一定的优势.但激光雷达在探测时也面临一些客观问题：即（1）难以捕捉快速移动的太空碎片；（2）对目标体穿透能力低；（3）外层空间的强干扰环境对激光雷达的不良影响等.这些问题在一定程度上限制了激光雷达在太空碎片探测方面的应用.本文针对太空碎片体积小、预警距离远和强干扰环境等特点，提出使用高性能瞬变电磁辐射源对远距离、小尺度的太空碎片进行探测.通过三维矢量有限元方法，分析了利用高性能瞬变电磁辐射源的优点，对比不同瞬变电磁辐射源的幅频特性，从发射机理上证明高性能瞬变电磁辐射源在辐射能力与频率带宽方面都优于传统瞬变电磁辐射源.并通过调整脉冲宽度，得到最适合探测本文太空碎片模型的辐射脉冲.最后通过电场分布图和多测道图对太空碎片的明显电场分异结果，证实了高性能瞬变电磁辐射源在探测远距离、小尺度太空碎片方面的有效性.  相似文献   

青藏高原及邻区未来地震活动性趋势数值分析          下载免费PDF全文

董培育  石耀霖  程惠红  乔学军 《地球物理学报》2020,63(3):1155-1169

区域中长期地震危险性数值分析研究,需要对其初始构造应力场有所了解,但目前以及未来一段时期内仍无法直接观测到深部孕震层区域的应力场状况.本文首先基于岩石库仑-摩尔破裂准则,利用青藏高原及邻区百年历史范围内的强震信息,来反演估算该区域的初始应力场.然后,考虑区域构造应力加载及强震造成的应力扰动共同作用,重现了历史强震的发展过程.然而对于初始应力场的反演估算,本文仅能给出区域其上下限的极限值,并不能唯一确定.因此,采用Monte Carlo随机法,进行大量独立的随机试验计算,生成数千种有差异的区域初始应力场模型,且保证每种模型都能令历史强震有序发生,但未来应力场演化过程不尽相同.最后,将数千种模型在未来时间段内的危险性预测结果集成为数理统计结果,据此给出了区域未来的地震危险性概率分布图.初步结果显示未来强震危险性概率较高地区集中在巴颜喀拉块体边界及鲜水河断裂带地区.  相似文献   

Inference of in situ stress from thermoporoelastic borehole breakouts based on artificial neural network     

Hua Zhang  Shunde Yin 《国际地质力学数值与分析法杂志》2019,43(16):2493-2511

The determination of in situ stresses is very important in petroleum engineering. Hydraulic fracturing is a widely accepted technique for the determination of in situ stresses nowadays. Unfortunately, the hydraulic fracturing test is time-consuming and expensive. Taking advantage of the shape of borehole breakouts measured from widely available caliper and image logs to determine in situ stress in petroleum engineering is highly attractive. By finite element modeling of borehole breakouts considering thermoporoelasticity, the authors simulate the process of borehole breakouts in terms of initiation, development, and stabilization under Mogi-Coulomb criterion and end up with the shape of borehole breakouts. Artificial neural network provides such a tool to establish the relationship between in situ stress and shape of borehole breakouts, which can be used to determine in situ stress based on different shape of borehole breakouts by inverse analysis. In this paper, two steps are taken to determine in situ stress by inverse analysis. First, sets of finite element modeling provide sets of data on in situ stress and borehole breakout measures considering the influence of drilling fluid temperature and pore pressure, which will be used to train an artificial neural network that can eventually represent the relationship between the in situ stress and borehole breakout measures. Second, for a given measure of borehole breakouts in a certain drilling fluid temperature, the trained artificial neural network will be used to predict the corresponding in situ stress. Results of numerical experiments show that the inverse analysis based on finite element modeling of borehole breakouts and artificial neural network is a promising method to determine in situ stress.  相似文献   

Seismic fracture evaluation of diaphragm joints in welded beam-to-box column moment connections     

Ching-Yi Tsai  Keh-Chyuan Tsai  Chao-Hsien Li  Chung-Che Wu  Ker-Chun Lin  Sheng-Jhih Jhuang 《地震工程与结构动力学》2020,49(13):1344-1362

Steel box columns are widely used in steel building structures in Taiwan due to their dual strong axes. To transfer the beam-end moment to the column, diaphragm plates of the same thickness and elevations as the beam flanges are usually welded inside the box column. The electro-slag welding (ESW) process is widely used to connect the diaphragms to the column flanges in Taiwan because of its convenience and efficiency. However, ESW may increase the hardness of the welds and heat-affected zones (HAZs), while reducing the Charpy-V notch strength in the HAZ. This situation can cause premature fracture of the diaphragm-to-column flange welds before a large plastic rotation is developed in the beam-to-box column joints. To quantify the critical eccentricity and the effectiveness of fracture prediction, this study uses fracture prediction models and finite element model (FEM) analysis to correlate the test results. In this study, two beam-to-box column connection subassembly tests are conducted with different loading protocols and ESW chamber shapes. To implement a fracture prediction model, the material parameters are established from circumferential notched tensile tests and FEM analysis. Test results indicate that the fracture instances can be predicted on the basis of the cumulative plastic deformation in the HAZs. Analytical results indicate that fracture instances and locations are sensitive to the relative locations of the ESW joints and beam flange. Tests also confirm that the possible fracture of the diaphragm-to-column flange joints can be mitigated by enlarging the chamber of the ESW joint.  相似文献   

断层附近地应力扰动带宽度及其影响因素   总被引：3，自引：3，他引：0  

翁剑桥  曾联波  吕文雅  刘奇  祖克威 《地质力学学报》2020,26(1):39-47

在建立正断层模型的基础上，利用三维有限元数值模拟方法研究了断层附近地层中的地应力变化规律。其结果表明，由于断层活动，在断层附近普遍发育应力扰动带；在应力扰动带范围内，地应力方向和大小发生明显的变化，断层中部附近应力值普遍较低，而断层端部的应力值通常异常增大。应力扰动带的分布范围主要受断层规模的控制，与断裂带的岩石力学性质、断层走向、断层面形态和边界应力条件等因素也密切相关。随断层长度和断距逐步增大，应力扰动带的宽度相应增加。断裂带的岩石越破碎，其岩石弹性模量越低，断层对地应力的影响宽度越大。断层走向与区域最大水平主应力方向越接近垂直、断距与断层长度的比值越大，区域内的差应力越大，则扰动带宽度与断层规模的比值也越大。选择渤海湾盆地BZ-X油田进行验证，在建立油田实际三维地质模型基础上，根据边界应力条件，利用三维有限元方法对沙河街组二段的地应力分布进行了数值模拟计算。根据断层周围的地应力变化，确定了应力扰动带的分布范围，断层附近应力扰动带宽度的分布规律与正断层模型分析结果相一致。   相似文献   

Evaluation of force-based and displacement-based out-of-plane seismic assessment methods for unreinforced masonry walls through refined model simulations     

Michele Godio  Katrin Beyer 《地震工程与结构动力学》2019,48(4):454-475

The performance of force-based and displacement-based seismic assessment methods for the life-safety limit state check of out-of-plane loaded unreinforced masonry walls is evaluated on the basis of refined numerical simulations. For this purpose, a discrete element model of a vertically spanning wall is built and validated against experimental results from static and dynamic test conditions. The model is then analysed for a large range of wall configurations. For each configuration, a static pushover analysis and a series of incremental dynamic analyses are run, the latter permitting to determine the capacity of the wall under dynamic loading. The accuracy of the assessment methods in predicting the acceleration at which the walls collapse is evaluated. It is found that the displacement-based method is more accurate, robust, and safe than the force-based method. The comparison also shows that for walls characterised by a relatively high ratio of axial load to Euler's critical load, both assessment methods lead to an overestimation of the wall capacity. As a remedy, a modification to the methods based on a recently developed mechanical model is put forward and tested. For the force-based method, it is additionally suggested to set for walls with relatively high overburden ratios the behaviour factor equal to 1. To ensure reproducibility of this study, all input and output files of the numerical simulations are made publicly available.  相似文献   

榍石LA-ICP-MS U-Pb定年中元素分馏的影响及校正研究     

靳梦琪  李艳广  王鹏  汪双双  黎卫亮 《岩矿测试》2020,39(2):274-284

同位素地质年代学是探索地质体时空演化及地球动力学等问题的基础学科,应用最为广泛的当属含铀副矿物的U-Pb定年技术。榍石具有相对较低的U-Pb体系封闭温度,并广泛发育于岩浆岩、各类变质岩、热液成因岩石以及少量沉积岩中,是一种理想的中高温地质事件定年矿物。利用电感耦合等离子体质谱法(ICP-MS)测定榍石U-Pb年龄时,不可避免地要解决高普通铅以及元素分馏效应对测试的影响。本文对榍石LA-ICP-MS实验过程中的元素分馏行为进行研究,采用相同基体的标准样品与未知样品对比,发现了榍石不同颗粒之间元素分馏行为不一致的现象;同时采用不同的元素分馏校正方法,分别应用于锆石、独居石和榍石进行对比研究,认为分馏行为一致的副矿物定年可以采用"指数法"和"均值法"对数据进行校正,但是对于榍石这种分馏行为不一致的副矿物,定年时只有采用"截距法"对数据进行校正才可以获得正确的年龄。进而将此结论应用于秦岭造山带老牛山地区岩浆成因榍石样品,得到的结果与锆石年龄一致,表明"截距法"可以避免分馏行为不一致导致的校正不准确的问题。本研究成果为榍石LA-ICP-MS U-Pb定年方法的完善提供了一种思路。  相似文献   

A probabilistic approach for computing water retention of particulate systems from statistics of grain size and tessellated pore network     

Richard Wan  Mehdi Pouragha  Mahdad Eghbalian  Jérôme Duriez  Tai Wong 《国际地质力学数值与分析法杂志》2019,43(5):956-973

The paper offers an analytical determination of the hydraulic properties of an unsaturated soil with reference to its retention curve, which describes the relationship between the volumetric water content and capillarity through matric suction. The analysis combines a particulate approach focused on the physics at the pore scale, including microstructural aspects, with a probabilistic approach where the void space and grain size are considered as random variables. In the end, the soil water characteristic curve of an unsaturated granular medium along a drying path can be derived analytically based on the sole information of particle size distribution. The analysis hinges on the tessellation of a wet granular system into an assemblage of tetrahedral unit cells revealing a pore network upon which capillary physics are computed with respect to pore throat invasion by a non-wetting fluid with evolving pendular capillary bridges. The crux of the paper is to pass from particle size probability distribution to a matching void space distribution to eventually reveal key information such as void cell and solid volume statistics. Making reasonable statistically based assumptions to render calculations tractable, the water retention curve can be readily constructed. Model predictions compare quite favourably with experimental data available for actual soils, especially in the high saturation range. Having a sound scientific basis, the model can be made amenable to address a variety of soils with a wider range of particle sizes.  相似文献   

银河系铝元素丰度研究     

马文娟  李宏杰  张波 《天文学报》2019,60(5):15-21

恒星的Al元素丰度可以为探索星团和星系的化学演化提供重要线索.通过系统分析银河系薄盘、厚盘、核球、银晕以及M4、M5等球状星团中恒星的[Al/Fe]随恒星金属丰度[Fe/H]的变化趋势,得出银河系薄盘、厚盘和核球恒星的[Al/Fe]随着[Fe/H]的增加而缓慢下降,而球状星团M4和M5恒星的[Al/Fe]随[Fe/H]增加没有下降趋势,这暗示Ia超新星对M4和M5恒星元素丰度的贡献比较小.详细研究了银河系恒星[Al/Fe]与[Mg/Fe]、[Na/Fe]的相关性,结果表明银河系场星的[Al/Fe]与[Mg/Fe]正相关,但在球状星团M4和M5恒星中未见此相关性;银河系盘星及M4和M5等球状星团恒星的[Al/Fe]与[Na/Fe]都存在正相关.  相似文献   

城市倾斜摄影实景三维模型数据质量检查方法研究与实践   总被引：1，自引：0，他引：1  

刘增良  陈思  陈品祥 《测绘通报》2019,(2):108-112

基于倾斜摄影可以快速获得高精度的城市实景三维模型，分析了实景三维模型数据的特点，探讨了实景三维模型数据质量检查的重点内容和质量元素，结合北京市大规模倾斜摄影实景三维数据质量检查实例，对实景三维数据质检问题与内容进行了总结，最后提出了实景三维模型数据的质量检查方法。  相似文献